Published 10/2022
MP4 | Video: h264, 1280×720 | Audio: AAC, 44.1 KHz
Language: English | Size: 1.26 GB | Duration: 3h 38m
Design of UART on FPGA using VHDL or verilog HDL programming
What you’ll learn
the student will learn how to design a half-duplex and also a full duplex transceiver.
the student will learn about baud rates, how to design one and the different lists of standard baud rates
the student will learn how to design a UART serial communication protocol and implement it on an FPGA Board
design UART transmitter AND receiver on FPGA with vhdl code, and simulate on logism
the student will learn how to convert serial bits to parallel bits and vice versa, and also implement in VHDL
the student will also learn some commonly used VHDL structural blocks like shift registers, parallelizer, serializer,
design UART transceiver on FPGA with vhdl code, and simulate on logism
Requirements
No external hardware needed. We would simulate the FPGA design in logism. Basic knowlegde of vhdl and how to use logism may be required.
Description
This is a practical course, that will teach you how to design your first UART project on FPGA using Verilog HDL programming language.In this course, you will learn the difference between a full duplex UART transmission and a half-duplex transmission including their technical difference. You will how to use LOGISM EDA tool to design, test and simulate logic circuits. You will a baud clock, learn how it is synthesized from system clock and how to calculate the frequency of generation.you will learn what a baud rate means and also learn the standard baud rates and how to generate them from the system clock. You will learn how to design and wire the receiver and transmitter to their baud clocks and how they are joined together to make up the transceiver.The course is divided into three sections: the receiver, the baud generator and transmitter.This a 17 video course. each module teaching about a particular part of the design.a lot of visuals, arrows, pictures were used to make the tutorials easy to understand.kindly use the logism circuit file while watching the tutorial for easy understanding. You will get the VHDL scripts and the logism circuit attached to lesson two. No hardware is required just your pc.It was kept brief and straight to the point.
Overview
Section 1: Introduction to UART communication
Lecture 1 01- Introduction
Lecture 2 Download zipped project folder
Lecture 3 02 – How to ask the instructor questions
Lecture 4 03 – UART configuration
Lecture 5 04 – introducing the logism design
Section 2: The Baudrate generator AND parity generator
Lecture 6 05 – How to set baud rate to carryout Oversampling
Lecture 7 06 – How to design the baud generator
Lecture 8 07 – simulating the baud generator in logism and testing oversampling
Lecture 9 How to ask the instructor questions
Lecture 10 08 – How to design and simulate the parity generator used for error check
Section 3: The Receiver
Lecture 11 09 – Design of a UART receiver sub circuit
Lecture 12 10 – testing and simulating the UART receiver in LOGISM PART1
Lecture 13 11 – testing and simulating the UART receiver in LOGISM PART2
Lecture 14 12 – Designing the receiver top circuit and merging it with the baud generator
Lecture 15 How to ask the instructor questions
Section 4: The transmitter
Lecture 16 13 – How to design a UART transmitter
Lecture 17 14 – Simulation and testing of UART transmitter in Logism PART1
Lecture 18 15 – Simulation and testing of UART transmitter in Logism PART2
Lecture 19 16 – How to design the transmitter top and add the baud generator
Section 5: Conclusion
Lecture 20 17 – Assignment and conclusion
Students with basic knowledge of VHDL, looking for a project to design
Password/解压密码www.tbtos.com
评论0